General Discussions

Photo Gallery

Feature Request

Prime

NSD (Nireeka Smart Display)

Installation Guides

Announcements

Hi Kevin, as you can see on this diagram, there are two outputs for front and rear lights coming out of the motor controller.

Nireeka Collector

Canada

Great !
Thanks Chris,
I have Three subsequent questions : 
Are they accessible on the Prime from the battery compartment or will i have to wire them directly from the motor ?
what is the voltage output ? if i'm not mistaken they are 6v<a href="/forum/profiles/username/500mA">@500mA</a> not 48v right ?
and  will the NSD control the headlight switching as the DP C18 does ?

Not a Nireeka owner

If you get that output from the motor, it means you're using the main battery and controlling it using the display buttons. They should be between 5V to 12V (I can check the exact output with the technical team) and the NSD can also control the headlight using handlebar buttons on the Prime model not Homie.

Yes i'd like to know the voltage if possible thanks Chris,
And where will i find the wires (on the prime) ? 
Will i have to dismount the motor cover or will i find them inside the battery compartment ?

The output is 6V 2.4W for the headlight. You need to dismount the motor cover to access the cables. They're installed on the motor, not the battery.

Ok great, thanks for your reply Chris, it answers a technical ticket i opened 6 days ago and still haven't got any returns, i'll close the ticket then.
Thanks again ;)

Is it possible to mount a 48v headlight on the Prime ? I believe that the DP C18 can switch on and off a headlight, but i suppose that it requires some special wiring on the motor cables, and on that topic, will the NSD control the headlight switching as the DP C18 does ? 
If not, this feature would be much appreciated.
Thanks

48v headlight wiring

I received the Torque Sensor Package today, but it did not come with any installation instructions.
Do you have any instructions or videos to help me with the installation process?

What I found when I actually did the work.
- Important: You need a 48V battery & 500w Moter.
  It ...

Dammit. Still leaves a 1mm gap between the bottom bracket frame and the RHS lockring. Maybe spacers are needed on both sides... I dunno.  Buy a motorbike

Australia

How do I install the Torque Sensor Package?

Post the pictures of your Nireeka ebike here.

This bike is a total piece of AWESOME! I absolutely never can get enough of riding it everywhere...

Nireeka Prime 

United States

Nireeka Ebike Gallery

Here is a quick demonstration of the final version of the NSD.

https://youtu.be/jLAH-ll7aBs

Specs:
We're using a touchscreen 6.53 inches smartphone-type display with 720x1600 pixels resolution on the NSD.

Features:
All the promised features are included.

Installation:
The NSD will be replaced with your current Nireeka display. It's plug&amp;play.

Connectivity: ...

So is this just an app for your phone that you can connect via bluetooth to a receiver that plugs in to the current display plug?

Nireeka Revenant IGG Earlybird

So I'm biking home tonight... and this thing shows up out of nowhere.   I now know that I can forcefully bunny-hop the Nireeka Homie in a pinch.   Emergency hopping a combined ~114kg (250lbs) was not fun, but I am not dead, and the bike took it like champ.   Almost 1000km ...

ObstacleWeb.jpg

Chassis Robustness & Emergencies

If you have a Bosch e-bike light kit, keep in mind that turning on the headlight also turns on the backlight at the same time. It uses a single switch to control both lights. 1. Locate the (+) button on one of the handlebars, next to the tiny LCD monitor. 2. To turn on the light, press and hold the (+) button for no more than three seconds.

ByKevin Loussert·May 4, 2021·Feature Request

ByHisaaki Kobayashi

ByYounes Shojaie

ByMax Shojaie